Система аксессуаров
11 профессиональных аксессуаров для полной гидроизоляционной системы. От монтажа до герметизации — всё в одном месте.
A5 Adhesive
Применение
Specialized adhesive for bonding XPS backer boards to substrates, board-to-board joints, and finish materials. Designed for strong bonding in wet-area board assemblies.
Упаковка
300 ml cartridge / 590 ml sausage pack
Примечания по установке
Apply evenly with a caulking gun on bonding surfaces. Press and secure until cured. Reinforce with suitable mechanical fixings where required.
S1 Waterproof Rubber Membrane
Применение
Applied at backer board joints, pipe penetrations, corners, and other wet-area details to form a flexible waterproof layer.
Упаковка
1 kg bucket
Примечания по установке
Ready to use. Apply two to three coats with a brush or roller, allowing proper drying time between coats. Reinforce joints with compatible mesh tape.
Pipe Collar
Применение
Waterproof sealing accessory for floor drains and pipe penetrations through tile backer board assemblies.
Упаковка
Multiple sizes for common pipe diameters
Примечания по установке
Slide the collar over the pipe and bond the base to the board surface with compatible waterproofing membrane. Ensure a tight fit around the penetration.
Corner Waterproof Fabric
Применение
Reinforcement fabric for inside corners, outside corners, wall-to-floor joints, and shower tray transitions.
Упаковка
Roll or pre-cut pieces
Примечания по установке
Embed the fabric into compatible waterproofing membrane at corners and transitions before tile installation.
Stainless Steel Washers
Применение
Used with screws to distribute fixing pressure on XPS tile backer board surfaces.
Упаковка
Bulk carton packaging
Примечания по установке
Install with compatible screws at the required spacing for the substrate and board thickness.
Anchors
Применение
Mechanical fixing accessory for attaching tile backer board to suitable wall or floor substrates.
Упаковка
Bulk carton packaging
Примечания по установке
Select anchor type according to substrate condition and follow the required fixing pattern.
Plastic Threaded Nails
Применение
Plastic fixing component used to support secure board installation where the project detail requires it.
Упаковка
Bulk carton packaging
Примечания по установке
Install through the board into the prepared substrate following the project fixing layout.
Reinforcement Blocks
Применение
Support blocks for local reinforcement, fixture zones, and wet-area board assembly details.
Упаковка
Carton or pallet packaging
Примечания по установке
Place reinforcement blocks at planned load or fixture areas before closing the tile assembly.
U / H Fixing Pieces
Применение
Fixing pieces used for board positioning, joint support, and selected system assembly details.
Упаковка
Bulk carton packaging
Примечания по установке
Use according to the board layout and project fixing detail. Confirm compatibility before installation.
Self-Adhesive Mesh Tape
Применение
Mesh tape for reinforcing board joints, seams, corners, and selected accessory transitions.
Упаковка
Roll packaging
Примечания по установке
Apply over clean joints, embed with compatible adhesive or waterproofing material, and cover fully before tiling.
Plastic Corner Trowel
Применение
Installation tool for smoothing waterproofing material and adhesive at corners and detail areas.
Упаковка
Single tool or carton packaging
Примечания по установке
Use during waterproofing and adhesive application to form cleaner corner details.
Waterproofing Accessories Guide
How accessories complete a backer board waterproofing system
Tile backer board projects need more than boards alone. Seams, corners, pipe penetrations, fixing points, tray transitions, and heavy fixture zones should be planned with the correct waterproofing accessories so distributors can offer a complete bathroom waterproofing system.
Board seams
Use mesh tape, suitable adhesive, or compatible waterproofing material to reinforce board-to-board joints before tile installation.
Corners and transitions
Inside corners, outside corners, wall-to-floor junctions, and shower tray transitions should be treated as priority waterproofing details.
Pipe penetrations
Pipe collars and sealing membrane help protect drain, water supply, and service penetrations through the board surface.
Mechanical fixing points
Washers, anchors, screws, and fixing pieces should match the substrate, board thickness, and project fixing pattern.
Distributor kit planning
Accessory programs can be grouped by board installation kits, shower tray kits, niche kits, pipe penetration kits, and sample kits.
Quote preparation
Before ordering, confirm accessory mix, carton or pallet packaging, destination market, and whether the order supports wholesale, OEM, or project supply.
Quick answer:
Waterproofing accessories for tile backer board systems are used to reinforce seams, corners, pipe penetrations, fixing points, shower tray transitions, and heavy fixture zones so the board system performs as a complete waterproof assembly.
Waterproofing Accessories FAQ
Which waterproofing accessories are usually used with tile backer board?
Common accessories include waterproof membrane, self-adhesive mesh tape, pipe collars, corner waterproof fabric, washers, anchors, plastic threaded nails, reinforcement blocks, and fixing pieces.
Why do shower systems need both boards and accessories?
Boards provide the main wall or floor substrate, while accessories reinforce seams, corners, pipe penetrations, tray transitions, and fixing points where leakage risk is higher.
Can distributors order accessories together with tile backer board?
Yes. Distributors can discuss accessory combinations together with tile backer board, waterproof backer board, shower trays, niches, and curbs for a more complete bathroom waterproofing system.